analog products division 561 e. elliot road #175 chandler, az 85225 tel: (480) 5 39 - 2900. fax: (602) 431 - 2288 www.protekanalog.com 1 pa2011 low rds on spdt analog switch. 95040 rev. 3 . 10 / 11 not for use in life support systems in v+ gnd dfn - 6 t o p v ie w 1 2 3 6 5 4 no (source 1 ) com nc (source 2 ) in v+ gnd 1 2 3 sc70 - 6 t o p v ie w 6 5 4 no (source 1 ) com nc (source 2 ) features ? l ow voltage op e r a t i on (1.8 v to 3.3 v) ? l ow o n - resistance - r o n : 1 . 8 ? at 2 . 7 v ? l ow ch a r g e i n jection ? l ow voltage l og i c com p at i ble ? dfn - 6 packag e or sc70 - 6 package b enefits ? r educ e d p o wer cons u m p t i on ? s i m p le lo g ic inter face ? h igh accuracy ? r educe bo a rd s p ace ? gu a r a nteed 2 v op e ration a pplications ? c ell u lar pho n es ? c omm u nicati o n systems ? p o rta b le t e st equ i pment ? b a t tery op e rated systems ? s a m p le and h old circu i t s ? adc a nd dac appl i cat i ons ? u sb 1.1 interfaces truth table logic nc no 0 on off 1 off on d escription the pa2011 is a low on - resistance, singl e - p ol e d o ub l e - thr o w mono l ithic cmos a na l og switch. it is d esig n ed for l o w v o ltage ap p licati o ns w i th g u aran t e e d o perati o n a t 2 v. the pa2011 is ide a l for p o rta b le and b a ttery pow e red eq u ipment, r e quir i ng h i gh p e rforma n ce and e f fici e nt u se of board s p ace. in a dd i ti o nal to the low o n - resistance (1.8 ? a t 2 . 7 v), charge inj e cti o n is l ess th a n 10 pc over t h e entire a n alog ra n ge. the switch co n ducts eq u ally well in b oth d i rect i ons w h en on, and b l ocks up to the po w er s u pply lev e l when off. br e ak - before - make is gu a rantee d . the pa2011 is mounted in a 1.6 x 1.6 mm dfn - 6 or sc70 - 6 lead p ackag e , r e ducing b oard s p acing by a p proximate l y 40 % pin configuration typical application ordering information temp. range package part number - 40 to 85 c dfn - 6 pa2011 dn - t7 sc70 - 6 pa2011sc - t7 sc70 - 6 pa2011sc - t13 pa2011 pa2011 hands free mic spkr internal mic spkr display p with soft modem audio codec & asic mic. pre - amp audio amplifier 95040
analog products division 561 e. elliot road #175 chandler, az 85225 tel: (480 ) 539 - 2900. fax: (602) 431 - 2288 www.protekanalog.com 2 pa2011 low rds on spdt analog switch. 95040 rev. 3 . 10 / 11 not for use in life support systems absolute maximum ratings t a = 25 c, unless otherwise noted parameter limit unit reference v+ to ground - 0.3 to 4.2 v in, com, nc, no 1 - 0.3 to (vcc+ 0.3v) continuous current (no,nc,com pins) 150 ma peak current (pulsed at 1ms, 10% duty cycle) 300 storage temperature - 65 to +150 c power dissipation 172 mw notes 1. signals on nc, no, or com or in exceeding v+ will be clamped by internal diodes. limit forward diode current to maximum cu rrent ratings specifications v+ = 2.0v test conditions unless otherwise specified: v + = 2.0 v , v i n = 0.4 v o r 1.6 v parameter symbol test conditions temp min typ max unit analog switch analog signal range v no ,v nc , v com full 0. 0 v cc v on - resistance r on v cc = 2.0 v, v c om = 0 .2v - 0.9v i no , i nc = 2 0ma, room full 3.5 5.5 5.5 ? switch off leakage current i off(no) or i off(nc) v + = 2.2 v , v n o , v nc = 0.5 v/1 . 5 v , v co m = 1.5 v/0.5 v room full - 1 - 10 - 1 - 10 na i com(off ) v + = 2.2 v , v n o , v nc = 0.5 v/1 . 5 v , v co m = 1.5 v/0.5 v room full - 1 - 10 - 1 - 10 channel on leakage current i com(on ) v+ = 2.2 v, vno, vnc = vcom = 0.5 v/1.5 v room full - 1 - 10 - 1 - 10 digital control input high voltage v in h full 1.5 v na input low voltage v in l full 0.4 input capacitance c i n full 4 pf input current i i n l o r i in h v i n = 0 or v+ full 1 1 a dynam ic characteristics turn on time t on v n o or v n c = 1.5 v , r l = 300 ? , c l = 35 pf room full 75 110 113 n s turn off time t o f f room full 37 71 76 break before make time t bbm room full 37 charge injection q in j room 7 pc off isolation oirr room - 62 db crosstalk x t a lk room - 69 no, nc off capacitance c no ( o f f) c nc ( o f f ) room 29 pf chanel on capacitance c o n room 85 power supply positive supply range v+ v in = 0 or v+ 1.8 3.3 v negative supply current i+ 0.01 1.0 a
analog products division 561 e. elliot road #175 chandler, az 85225 tel: (480 ) 539 - 2900. fax: (602) 431 - 2288 www.protekanalog.com 3 pa2011 low rds on spdt analog switch. 95040 rev. 3 . 10 / 11 not for use in life support systems speci fications v+ = 3.0v test conditions unless otherwise specified: v + = 3 .0 v 10% , v i n = 0.4 v o r 2.0 v parameter symbol test conditions temp min typ max unit analog switch analog signal range v no ,v nc , v com full 0. 0 v cc v on - resistance r on v cc = 2.7 v, v c o m = 0 .9v - 1.5v i no , i nc = 5 0ma, room full 1.8 2.7 2.9 ? r on matching ? r on 0.2 r on flatness r on (flat) 0.2 0.5 switch off leakage current i off(no) or i off(nc) v + = 3.3 v , v n o , v nc = 1.0 v/ 3.0 v , v co m = 3.0 v/ 1.0 v room full - 1 - 10 - 1 - 10 na i com(off ) room full - 1 - 10 - 1 - 10 channel on leakage current i com(on ) v+ = 3.3 v, v no , v nc = v com = 1.0 v /3.0 v room full - 1 - 10 - 1 - 10 digital control input high voltage v in h full 1.5 v na input low voltage v in l full 0.4 input capacitance c i n full 4 pf input current i i n l o r i in h v i n = 0 or v+ full 1 1 a dynamic characteristics turn on time t on v n o or v n c = 2.0 v , r l = 300 ? , c l = 35 pf room full 45 75 77 n s turn off time t o f f room full 29 59 62 break before make time t bbm room full 16 charge injection q in j cl = 1 nf, vgen = 0 v , rgen = 0 ? room 2 pc off isolation oirr rl = 50 ? , cl = 5 pf, f = 1 mhz room - 62 db crosstalk x t a lk room - 69 no, nc off capacitance c no ( o f f) c nc ( o f f ) vin = 0 or v+, f = 1 mhz room 28 pf chanel on capacitance c o n room 84 power sup ply positive supply range v+ v in = 0 or v+ 1.8 3.3 v negative supply current i+ 0.01 1.0 a notes: 1. room = 25 c, full = as determined by the operating suffix. 2. typical values are for design aid only, not guaranteed nor subject to production te sting. 3. the algebraic convention whereby the most negative value is a minimum and the most positive a maximum, is used in this dat a sheet. 4. guarantee by design, no t subjected to production test. 5. vin = input voltage to perform proper function. 6. gu aranteed by 5 v leakage testing, not production tested.
analog products division 561 e. elliot road #175 chandler, az 85225 tel: (480 ) 539 - 2900. fax: (602) 431 - 2288 www.protekanalog.com 4 pa2011 low rds on spdt analog switch. 95040 rev. 3 . 10 / 11 not for use in life support systems 0 1 2 3 4 5 6 v c o m C analo g v oltag e (v) v + = 3. 0 v i s = 5 0 ma 6 5 t = 25 c 6 5 a: 8 5 c b : 2 5 c c : - 40 c 4 3 v + = 2. 0 v i s = 2 0 ma 4 3 v + = 2. 0 v i s = 2 0 ma a b c v + = 3. 0 v i s = 5 0 ma 2 1 v + = 3. 0 v i s = 5 0 ma v + = 3.3 v i s = 10 0 ma 2 1 a b c v + = 3.3 v i s = 10 0 ma a b c 0 0 1 2 3 4 v c o m C analo g v oltag e (v) 5 6 0 r o n vs. v co m and s u p p ly vol t age r o n vs. a n alog voltage a n d t em p erature 10000 1000 v+ = 3.3 v v i n = 0 v 1 0 ma 1 ma 10 0 a v + = 3.3 v 100 1 0 a 1 a 10 0 na 10 1 0 na 1 na 1 - 60 - 40 - 20 0 20 40 60 80 100 t empe r ature (c) s u p p ly c u r re n t vs. t em p erat u re 10 0 pa 100 1 k 10 k 100 k 1 m 10 m 100 m input switching f requency (hz ) s u pply current vs. i n put sw i tchi n g f req u ency 10000 v + = 3.3 v 250 200 v + = 3.3 v 1000 100 10 i c o m ( o ff) i o n ( o ff ) / i nc ( o ff ) i c o m ( on) 150 100 50 0 - 50 - 100 - 150 i c o m ( on) i o n ( o ff ) / i nc ( o ff ) i c o m ( o ff) 1 - 60 - 40 - 20 0 20 40 60 80 100 t empe r ature (c) l e akage c urrent vs. te m perat ure - 200 - 250 0 1 2 3 4 5 v c o m , v n o , v nc , C analo g v oltag e (v) l eakage vs. an a log v o lta g e r on C on - r e s i st an c e (? ) r on C on - r e s i st an c e (? ) i+ C supp l y curr e nt (a) i+ C supp l y curr e nt (na) leakage curre n t ( p a) leakage curre n t ( p a) typical characteristics t a = 2 5 c, u n les s o t h e r wis e n ot ed
analog products division 561 e. elliot road #175 chandler, az 85225 tel: (480 ) 539 - 2900. fax: (602) 431 - 2288 www.protekanalog.com 5 pa2011 low rds on spdt analog switch. 95040 rev. 3 . 10 / 11 not for use in life support systems 90 80 70 60 50 40 30 20 10 0 t o n v + = 2 v t o n v + = 3 v t of f v + = 2 v t of f v + = 3 v t of f v + = 3 .3 v t on v + = 3.3 v 10 0 10 20 30 40 50 60 70 80 90 loss x t a l k oirr v + = 3.3 v r l = 50 - 60 - 40 - 20 0 20 40 60 80 10 0 t empe r ature (c) 10 0 k 1 m 1 0 m 10 0 m 1 g frequency (hz) switc h ing ti m e vs. t em p erature a nd s u p p ly voltage insertion los s , off - i solation, crosstalk vs. fr eq u enc y 3.0 30 2.5 20 2.0 10 v + = 2 v v + = 3.3 v 1.5 0 v + = 3 v 1.0 10 0.5 20 0.0 0 1 2 3 4 5 6 7 v + C suppl y v oltag e (v) swit c hing t h resh o ld vs. s u p p ly vol t age 30 0 1 2 3 4 5 6 v c o m C analo g v oltag e (v) c h arge i n jecti o n vs. anal o g v o ltage loss, o i rr, x t alk (db) t on / t off C sw it chin g t i m e ( n s) q C char g e inj e cti o n ( p c) C s wi tc hin g t h res h old (v) v t typical characteristics t a = 2 5 c , u n les s o t h e rwis e n o t e d
analog products division 561 e. elliot road #175 chandler, az 85225 tel: (480 ) 539 - 2900. fax: (602) 431 - 2288 www.protekanalog.com 6 pa2011 low rds on spdt analog switch. 95040 rev. 3 . 10 / 11 not for use in life support systems switch input v+ v+ no or nc in com switc h output r l c l v o u t + 3 v 0 v 50% t r < 5 ns t f < 5 ns 0. 9 x v o u t logic input gnd 0 v 300 3 5 pf 0 v t o n t off r l v no v nc no nc v+ v+ com r l c l v o 300 3 5 pf in gnd v o 0 v v+ v ge n + r gen 3 v nc or no in v+ gnd com v o u t c l v o u t in on ? v o u t o f f on q = ? v o u t x c l logic input switch output c l (includes fixture and stray capacitance) r l logic "1" = switch on logic input waveforms inverted for switches that have th e opposit e logi c sense. v o ut = v c o m + r on f ig u r e 1. swi t chi n g t ime logic inpu t 3 v 0 v t r <5 ns t f <5 ns v n c = v n o switch output 90% t d t d c l (includes fixture and stray capacitance) f ig u r e 2. break - b ef o r e - make i n terval fi g ure 3. c harge injec t ion i n depend s o n switc h confi guration : inpu t polarity determined by sense of switch. test circuits
analog products division 561 e. elliot road #175 chandler, az 85225 tel: (480 ) 539 - 2900. fax: (602) 431 - 2288 www.protekanalog.com 7 pa2011 low rds on spdt analog switch. 95040 rev. 3 . 10 / 11 not for use in life support systems v+ 1 0 nf r l com v+ com nc or no gnd in 0 v , 2. 4 v o ff i s o l a t i o n = 2 0 l o g v nc/ no v c o m analyzer f ig u r e 4. o f f - isola t ion 1 0 nf v+ v+ com 0 v , 2. 4 v in gnd nc or no meter hp4192a imp edance analyzer o r equivalent f = 1 mhz fi g ure 5. c ha n nel off/on ca p acita n ce test circuits
analog products division 561 e. elliot road #175 chandler, az 85225 tel: (480 ) 539 - 2900. fax: (602) 431 - 2288 www.protekanalog.com 8 pa2011 low rds on spdt analog switch. 95040 rev. 3 . 10 / 11 not for use in life support systems package outline and dimensions dfn - 6 dim millimeters inches min max min max p1 1.5 1.7 0.060 0.066 p2 1.5 1.7 0.060 0.066 p3 0.45 0.65 0.018 0.026 l1 0.23 0.27 0.009 0.012 l2 0. 20 0.30 0.008 0.012 l3 0.01 0.09 0.001 0.003 p 0.50 0.50 0.020 0.020 g1 0.90 1.10 0.035 0.043 g2 0.38 0.43 0.013 0.017 tape and reel specifications (dimensions in mm) reel dia a0 b0 k0 d e f w p0 p2 p t - max 178 (7) 1.800.10 1. 800.10 0 .800.10 1. 5 00.10 1.75 0.10 3.50 0. 05 8 .0 0 0.3 0 4.00 0.10 2.0 00. 05 4.00 0.10 0.25 l3 p3 side view 1.1mm 0.50mm 0.50mm 1.8 mm 0.48 mm 0.33 mm recommended land pattern p0 p2 d a0 b0 p e f w pin 1 indicated by dot k0 top cover tape t 10 pitches cumulative tolerance on tape 0.2 p1 p2 g2 g1 l1 p l2 top view bottom view
analog products division 561 e. elliot road #175 chandler, az 85225 tel: (480 ) 539 - 2900. fax: (602) 431 - 2288 www.protekanalog.com 9 pa2011 low rds on spdt analog switch. 95040 rev. 3 . 10 / 11 not for use in life support systems package outline and dimensions sc70 - 6 lead dim millimeters inches min max min max a 1.90 2.15 0.074 0.084 b 1.15 1.35 0.045 0.055 c 0.80 1. 00 0.031 0.040 d 0.15 0.30 0.006 0.012 e 0.65 bsc 0.0255 bsc f 1.30 bsc 0.0512 bsc g 0.80 1.10 0.031 0.043 j 0.08 0.25 0.003 0.010 k 2.00 2.20 0.078 0.086 l 0 0.10 0 0.004 m 0.26 0.46 0.010 0.018 land pattern 1 0.50 0.020 2 1.30 0.051 3 0.65 0.026 4 1.72 0.068 5 0.60 0.024 6 1.11 0.044 7 2.33 0.092 tape and reel specifications (dimensions in mm) reel dia a0 b0 k0 d e f w p0 p2 p t - max 178 (7) 2.25 0.10 2.34 0.10 1.22 0.10 1. 5 00.10 1.75 0.10 3.50 0. 05 8 .0 0 0.3 0 4.00 0.1 0 2.0 00. 05 4.00 0.10 0.25 life support p o licy protek a nalog's products are not authorized for u se as critical components i n life supp ort dev i ces or systems without the e xp r ess written a pproval of the presid e nt of protek devices. g c b m l 0 - 8 j 4 3 2 1 7 6 5 top view side view end view recommended land pattern p0 p2 d a0 b0 p e f w pin 1 indicated by dot k0 top cover tape t 10 pitches cumulative tolerance on tape 0.2 e d k f a 3 1 6 4
|
